H801 RGB+W+W

elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

Post

Button3.rar
You do not have the required permissions to view the files attached to this post.
User avatar
Xoggo
Posts: 182
Joined: Sun Mar 29, 2020 10:03 pm
Location: Zbąszynek

Post

elmaya wrote: Wed May 13, 2020 7:55 am
Thank you
Robi
Posts: 13
Joined: Fri Jan 05, 2018 8:23 pm

Post

¿Es posible agregar un sensor de temperatura? BME280? DHT22? DS18B20?
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

Post

Robi wrote: Sun Aug 30, 2020 6:49 pm ¿Es posible agregar un sensor de temperatura? BME280? DHT22? DS18B20?
En su momento hice esta versión que incorpora un sensor de temperatura DS18B20 conectado a Gpio 2.
En el H801 Gpio 2 esta marcado como RX.

57890715-ed861580-7838-11e9-95e9-b256adf0e681.png

RGB_w_w_DS18B20_Gpio2_DOUT_8Mbit.rar
You do not have the required permissions to view the files attached to this post.
Patryk
Posts: 2776
Joined: Mon Jan 07, 2019 7:51 pm
Location: Rybnik

Post

elmaya wrote: Fri Mar 13, 2020 4:04 pm Corregidos algunos errores con la memoria de último estado (encendido – apagado) y operación correcta sin conexión.
Se ha implementado el control independiente de los 3 canales (RGB + 1ªW + 2ªW).
Simple clic en el pulsador cambia el estado del canal RGB (encendido – apagado).
Doble clic en el pulsador cambia el estado del canal primer canal W (encendido – apagado).
Triple clic en el pulsador cambia el estado del canal segundo canal W (encendido – apagado).


Supla_RGB_W_W_newLib_V3_H801_DOUT_8Mbit.rar
@elmaya is testing your soft - great !!!
But I would like LED RED
1. During installation - was blinking rapidly.
2. No WiFi or no internet - flashes slowly.
3. If everything is fine - turn it off.
User avatar
lukfud
Posts: 2201
Joined: Thu Nov 23, 2017 11:33 pm
Location: Warszawa

Post

Patryk wrote: Fri Oct 30, 2020 10:50 pm @elmaya is testing your soft - great !!!
But I would like LED RED
1. During installation - was blinking rapidly.
2. No WiFi or no internet - flashes slowly.
3. If everything is fine - turn it off.
Sprawdź tą wersję ;)
You do not have the required permissions to view the files attached to this post.
https://www.facebook.com/groups/supladiy/
Patryk
Posts: 2776
Joined: Mon Jan 07, 2019 7:51 pm
Location: Rybnik

Post

@elmaya Friend,
Which version of SuplaDevice have you used?
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

Post

Patryk wrote: Sun Nov 01, 2020 8:45 pm @elmaya Friend,
¿Qué versión de SuplaDevice ha utilizado?
Creo recordar que era esta:

Supla_RGB_W_W_newLib_V3_H801_DOUT_8Mbit.rar
You do not have the required permissions to view the files attached to this post.
Patryk
Posts: 2776
Joined: Mon Jan 07, 2019 7:51 pm
Location: Rybnik

Post

Gracias !!!
elmaya
Posts: 1482
Joined: Wed Jun 27, 2018 5:48 pm
Location: El Saucejo - Sevilla

Post

Creo que solo en dos cosas:
“1M (no SPIFFS)” debe de ser con SPIFFS “1M (128 SPIFFS)”
Arduino Esp8266 Board manager 2.7.4

Return to “Ideas y conceptos”